Why Use Machine Control for Heavy Equipment

Whitehurst Sand Company has been a tremendous partner of ours for the past 5 plus years and we can not thank them enough for the very kind words. We are grateful that we are able to provide them with the level of service that they need to stay up and running

The two types of machine control:

• Machine guidance
• Machine automation

Machine Control is split into two categories.

Machine guidance. The system compares the position of the tool with the 3D design of the site and uses the difference between those values to tell the operator what’s going on. It’s then up to the operator to drive the machine to its required position and stop when the job is done. The 3D design normally comes in the form of triangulated surface models or digital terrain models (DTM), which are uploaded using a USB stick in the case of a single machine.

Machine automation. Machine automation does the same calculations for the position but has an added interface that takes some of the work out of the operator’s hands. By using hydraulics or connecting to systems on the machine, machine automation can position the machine itself and meet the desired value, such as digging to the correct depth. This is generally found on dozers, graders, and paving solutions, where accuracy can be achieved much more easily than using a guidance-only system.

The trend in the industry is for guidance systems to become more and more automated. The excavator system especially has seen many developments over the past 12 months, including the semi-automatic excavator. We have drilling systems that can stop drilling automatically when the machine control tells the system that it’s hit the desired depth, and solutions for dozers and graders interface with the machines’ hydraulic system for an automated operation.

Watch our service crew install a TOPCON MC-i4 for Iron Horse Contractors. By the time our boys are finished, Iron Horse will have the most reliable machine control system available. The rugged design allows for ultra reliability in even the harshest site conditions. The MC-i4 was subjected to IP67 testing specifications which require the hardware to have extreme protection against moisture and dust as well as stringent drop and vibration requirements.

How it works:

• positioning data

Generally, machine control requires some instruments to position itself, and there are a few ways of doing this. Firstly, in simple cases, if you’re only concerned with height, for example, you can use a rotating laser. We refer to this as a 2D machine control system. Secondly, you can use a total station tor laser scanner to acquire position and height, which is true 3D machine control. This is used for applications that require a high level of accuracy: like trimming and grading applications for roads and rail. Finally, the most common positioning type for machine control is GNSS, which will position the machine to 3D accuracy of roughly 30mm. In all these cases, the initial positioning is not done to the position of the tool itself, so there are other sensors installed to transfer the position from where the sensor sits on the back of the machine to the contact point of the tool.

Benefits:

1. Machine operators can work more efficiently with better access to information

Machine control lets operators see all the design information on their screen in the vehicle’s car, which means they’re not relying on printed documents for levels or relying on others on-site to tell them. They can check the accuracy of their own work and easily visualise the finished product by looking at the model on the screen. All this extra information allows them to get the work right first go, reducing any rework.

For the engineer, machine control means that there are no pegs or batteries to knock in for hours on end as the information is all there in the machine. They don’t need to have someone checking the work constantly because the operators can now check the work themselves. Therefore, the time that they need to spend near heavy machinery – a common location for accidents – is reduced. 

 3. Environmental targets are easier to meet due to more efficient working
Machine control means that there’s less material waste as operators can be more accurate in their work. This also means less fuel is consumed, both factors in helping construction companies meet the project’s environmental targets. 

 4. The risk of damaging utilities – and delaying the project – is reduced.
With the previously collected data on the location of underground utilities, you can upload this information to the machine control system and set an avoidance zone, thereby significantly reducing the risk of hitting cables or pipework and damaging a utility. It’s easy to set your avoidance zone and a trigger distance where the machine control system will alert the operator to danger. As soon as the machine goes within the trigger distance, the system sends a warning with an audible alarm, and the screen goes red.

 5. Reporting is made easier with simple data capture
It’s possible to get data back from the machine control system in the form of measured points for the as-built reporting. The system simply creates a CSV file that populates with those points by pressing the point logging button.